home *** CD-ROM | disk | FTP | other *** search
/ Your Choice 3 / Your Choice Software Collection 3.iso / dos / copyq317 / whats.new < prev   
Text File  |  1994-09-28  |  8KB  |  174 lines

  1.                         What's New in CopyQM 3.17
  2.  
  3.                                 Sydex, Inc.
  4.                               P.O. Box 5700
  5.                             Eugene, OR  97405
  6.                               (503) 683-6033
  7.  
  8.                              September, 1994
  9.  
  10. CopyQM's diskette I/O routines now support IRQs from 2 through 15, instead
  11. the previous 2 through 8.  This allows 16-bit controller cards that can use
  12. the higher IRQ numbers, such as the Adaptec SCSI cards to operate as secondary
  13. controllers with CopyQM.
  14.  
  15. A new command-line keyword, "GO" has been added.  This keyword will suppress
  16. the "Re-insert Master Diskette" message that appears when reading the first
  17. diskette of a session.  If a diskette is in the source drive, CopyQM will
  18. immediately begin processing it.  This is useful when a diskette has just
  19. been created and needs to be processed immediately without operator inter-
  20. vention.
  21.  
  22. When the RECORD=/ASK keyword is used, a filename with "?" characters may
  23. be used in response to the file name prompt.  The effect is the same as
  24. if the filename were given directly with the RECORD=filename keyword.
  25. That is, for a file name of A???, files named A001, A002, A003... will
  26. be created.
  27.  
  28. When the PLAYBACK=/ASK keyword is used, file names with "?" and "*"
  29. characters may be used in response to the file name prompt.  The effect
  30. is to play back all image files satisfying the file specification, then
  31. request a new file name.  Files are accessed in alphabetic order.
  32.  
  33. A small bug in the self-extractor was corrected in CopyQM Plus.
  34.  
  35.  
  36.                         What's New in CopyQM 3.16
  37.  
  38. You can now copy diskettes containing flawed areas by specifying the FLAW
  39. keyword on the CopyQM command line, or by selecting the "Ignore master data
  40. errors?" choice with CQMenu.  Please note that the data content of erroneous
  41. sectors is NOT repaired, but as much data as possible will be recovered from
  42. the bad sectors.  Consult the on-line help for more information.
  43.  
  44. The self-extracting file processor in CopyQM Plus has a bug repair.  If
  45. an unusable destination diskette was used when executing a self-extracting
  46. image file, the "Make another copy?" processing would not recover correctly
  47. and an "Image file corrupt" message would result.  Note that the self-
  48. extracting file would operate correctly the next time it was executed.
  49.  
  50. CopyQM Plus users can now invoke SHELL or OVERLAY procedures when an image
  51. file is being written.  The sequence of events is exactly the same as when
  52. diskette copies are being produced.
  53.  
  54.                         What's New in CopyQM 3.15
  55.  
  56. CopyQM now supports writing on up to twelve (!) destination drives.  You
  57. must have an EGA or VGA display card when more than six destination drives
  58. are being used.
  59.  
  60. In RECORD= mode, CopyQM now checks for a pre-existing file of the same name
  61. as the image file to be written.  If one exists, a prompt is issued, giving
  62. you the opportunity to exit CopyQM before overwriting the file.
  63.  
  64. The first master diskette in a session is prompted for with the message
  65. "Re-insert Master".  The second and succeeding masters are requested
  66. with the message "Insert Next Master".
  67.  
  68. We've made a couple of bug fixes related to multi-drive copying.  One is
  69. an out-and-out goof--the display didn't correctly show which drive in a
  70. multi-drive set was really writing.  The other is a subtle one and is
  71. concerned only with 1.2M and 360K drives used to make the same 360K
  72. copy--not a good idea, but supported at any rate.
  73.  
  74. CopyQM Plus users will note that the drive speed test now adds one more
  75. digit of significance to the reported spin rate.
  76.  
  77.  
  78.                      What's New in CopyQM 3.14
  79.  
  80.  
  81. If the BLIND option has not been specified and a non-DOS, non-Macintosh
  82. diskette is read, a prompt now appears allowing a change to BLIND copying
  83. mode.  However, you should be aware that the non-DOS error message can
  84. also appear when a DOS diskette is infected with a boot-sector virus,
  85. such as the "Stoned" virus.
  86.  
  87. Auto-sense for E-Ten Chinese-language display software has been removed
  88. due to conflicts with some ATI Technologies VGA display cards.  If a
  89. restricted character set is desired, the "7BIT" command-line option
  90. should be used.
  91.  
  92.                         What's New in CopyQM 3.13
  93.  
  94. CopyQM Plus now creates self-extracting image files directly, without
  95. the use of MAKESXD.  The SELFEXTRACT (abbreviated SELF) keyword, when
  96. used with RECORD, causes a self-extracting file to be recorded.  When
  97. self-extracting files are produced, about 40K of additional base RAM
  98. is required for operation.  In general, CopyQM requires a base RAM
  99. space of at least 350K for execution.  Of course, the more memory the
  100. better--i.e., faster--operation.
  101.  
  102. MAKESXD now does its work in a single pass, without any additional disk
  103. space required for temporary files.
  104.  
  105. BIOS support has been improved to accomodate a few less-IBM-conforming
  106. BIOS sets.
  107.  
  108. Code has been added to enabled interrupts at critical points.  We've seen
  109. some BIOS code that doesn't seem to re-enable interrupts after they've
  110. been disabled.
  111.  
  112. Support has been improved for 2.88M drives and controllers.  However,
  113. CopyQM requires that 2.88M drives be jumpered for auto media-sensing
  114. to work with the DIRECT diskette controller access modes.  If your
  115. 2.88M drives are not not jumpered in this manner, you can either reset
  116. the jumpers or use BIOS access.
  117.  
  118. The SCANDISK utility in MS-DOS 6.2 sometimes reports a spurious boot-
  119. sector and/or FAT error on diskettes generated with the CONVERT= option,
  120. though MS-DOS CHKDSK finds no problem.  We've traced this to SCANDISK's
  121. insistence on a certain media byte for a given media type. Interestingly,
  122. in Microsoft's own words:  "Beginning with DOS 2.x, the usefulness of the
  123. disk ID byte in the FAT was reduced and it now considered meaningless..."
  124. Not being ones to argue a minor point, we now insert the proper media
  125. media byte in CONVERT-ed diskettes and SCANDISK is happy.  Sigh...
  126.  
  127.  
  128.                         What's New in CopyQM 3.12
  129.  
  130. CopyQM 3.12 contains a few minor changes to version 3.11:
  131.  
  132.         1.   Support for the E-Ten Chinese language system has been
  133.              incorporated.  Users who use other double-byte systems
  134.              can force the use of non-extended codes by means of the
  135.              /7BIT command-line switch on any of the CopyQM product
  136.              set.
  137.  
  138.         2.   A bug occurred when a BLIND mode copy was attempted where
  139.              FIRST= did not equal 1.  Only one sector per track would
  140.              be seen when CopyQM was run in Direct hardware access mode.
  141.  
  142.         3.   A few Windows API calls have been added to the Direct I/O
  143.              routines.  CopyQM should run as a background task in direct
  144.              hardware controller access mode  under Windows 3.1.  However,
  145.              IBM OS/2's implementation of Windows and their DOS box appear
  146.              to ignore these API calls, so running as a background task in
  147.              OS/2 will still result in occasional "DRIVE NOT READY" errors.
  148.  
  149.         4.   Normally, CopyQM and its utilities will access the screen memory
  150.              directly in order to draw displays as quickly as is possible.
  151.              However, if the following switch is used, CopyQM and its
  152.              utilities will use the video BIOS to create screen displays:
  153.  
  154.                      /CRTBIOS
  155.  
  156.              This can be abbreviated to /CR.  For example, if a copy using
  157.              drives A: and B: is to be performed, the following command line
  158.              could be used:
  159.  
  160.                      COPYQM A: B: /CRTBIOS
  161.  
  162.              Similarly, all CopyQM utilities, including CQMENU, CINSTALL,
  163.              ICOMMENT, MAKESXD (CopyQM Plus only), DRMAINT (CopyQM Plus only)
  164.              will accept the /CRTBIOS switch.  The configuration viewer,
  165.              VIEWCONF, accepts this switch, but ignores it, as VIEWCONF
  166.              always uses the CRT BIOS.
  167.  
  168.              Text-to-speech translator users may want to experiment with
  169.              the switches /7BIT and /MONO to reduce the number of non-text
  170.              characters on the screen.  The /7BIT switch forces the use of
  171.              the lower 128 codes in the ASCII set; that is, line-drawing and
  172.              character graphics are not used.  The /MONO switch forces use of
  173.              a monochrome display set.
  174.